How to Prevent Slips, Trips and Falls | Safety Culture (2023)

What are slips, trips and falls?

Slips, trips and falls are the most common workplace hazards. They subject many workers to sprains, strains, cuts, bruises, broken bones and other injuries. In worst cases, they can also cause death, especially in high-risk occupations such as construction. However, with proper training and security practices, companies can protect their employees from these threats.

Swimming pants

Slips and falls occur when there is little or no grip between the shoe and the walking surface. A person can lose their balance because there is too little friction to keep their feet on the ground. For example, if a supermarket worker is running down a wet aisle, he is likely to slip and fall on the floor.

trip

A trip, on the other hand, occurs when the foot hits an object or lands on a lower, uneven surface. Or it can upset a person's balance and cause them to lose their balance. For example, an electrical engineer might trip over a tangled wire on the floor.

belong

Falls are leading cause of death for construction workers.They can happen to anyone if they fall and fall too far from the center of balance. For example, an electrician canfell off a ladderwhen installing the bulb.

thisOccupational Safety and Health Administration (OSHA)Divide them into two types:

  • down to the same level— appears on the same desktop
  • lower level— Happened under one's communal deskWorking at heights

Number of slips, trips and falls

thisU.S. Bureau of Labor Statistics (BLS)Slips, trips and falls occurred at alarming rates in 2020, according to the report. Their latest data shows that slips, trips and falls are the leading causes of fatal and non-fatal injuries in the workplace.

This section contains key data points fromFatal Occurrences at Work Checklist (CFOI)IOccupational Injury and Illness Investigation (SOII).

fatal injury

immortal wound

  • Number of slips, trips and falls exceeded211,640 casesw 2020 r。
  • is one ofThe Three Most Common Causes of Nonfatal Accidents at WorkThis includes non-working days.
  • more than halffrom these caseson the ground,Walking street, Iground.
  • A large proportion of these incidents are caused bydown to the same level.

industries at risk

thisNational Institute for Occupational Safety and Health (NIOSH) Centers for Disease Control (CDC)The following industries with the highest risk of slipping, slipping and falling are listed:

  • healthcare support
  • Maintenance and drainage of buildings
  • Shipping and Materials
  • construction and mining

Common Causes and Risk Factors

Slips, trips and falls can happen for many reasons, from uneven work surfaces to dangerous positions on ladders. Understanding the causes can help managers assess risk factors and develop preventative methods.

This section lists the causes and risk factors for each risk.

Swimming pants

  • Spilled liquids (such as water, mud, grease, oil, food, blood, etc.)
  • Dry product spills (e.g. dust, powder, shavings, granules, plastic casings)
  • Weather hazards (e.g. ice, snow)
  • Loose, unjoined rugs and rugs
  • Concrete, ceramic or marble floors
  • recently waxed floors
  • sloped or uneven walking surfaces
  • wet, muddy, greasy boots
  • Ramps or boards without slip or non-slip surfaces
  • metal surface
  • go up the stairs

trip

  • mess on the floor
  • limited visibility
  • bad light
  • Unsightly, wrinkled carpet or rugs
  • Bare wires, cables, hoses and extension cords
  • Open drawers, cabinets, doors, and more.
  • bumpy path
  • unmarked steps or ramps
  • Floor tiles and floor tiles are missing
  • damaged steps
  • Irregular, incorrect or uneven steps

belong

  • weak or damaged ladder
  • Overhangs without proper railings
  • Transport heavy objects
  • Do not use protective handrails on scaffolding
  • unprotected edge
  • The ladder is not securely installed
  • abuse of fall protection andHigh access equipment

Occupational Safety and Health Regulations

thisOccupational Health and Safety Standard 1910 Part D (Walkable Work Surfaces)Defines common standards for walking and working surfaces. These areas include aisles, storage areas, service rooms, work areas, etc.

this1910.22 regulationsDescribe the various points about safe work surfaces as follows:

  • Keep the work area floor clean, tidy and dry.
  • Maintain efficient drainage when working on wet surfaces.
  • Keep surfaces free of hazards such as sharp objects, loose planks, corrosion, spills, spills, snow and ice.
  • Make sure your desktop computer can handle the maximum expected load.
  • Ensure safe access to and from walking surfaces.
  • Check the desktop and keep it in good condition.
  • Repair dangerous floors as soon as possible.

7 Tips to Prevent Slips, Trips and Falls

Fortunately, most slips, trips and falls are preventable. use appropriate security tools andeducateEmployees, companies can prevent such incidents from happening in their workplaces.

Safety managers should consider the following to protect the workplace and its co-workers from slips, trips and falls.

How to Prevent Slips, Trips and Falls | Safety Culture (1)

How to Prevent Slips, Trips and Falls in the Workplace

1. Do housework

A slip-free workplace starts with cleaning. Removing clutter helps to tidy up the floor and make it walkable for everyone. in principlegood cleaning habitsThere are the following tips:

  • Drawers, cabinets, and other storage items should be closed when not in use.
  • Throw rubbish into the correct bin.
  • Place the chest away from the main room.
  • Conceal cords, extension cords, and cords in the protective case.

2. Provide adequate lighting in pedestrian areas

Poorly lit sidewalks can also cause trips and falls. When they can't see their way, they may bump into objects and fall to the ground.

Workers can better navigate the space if there is enough light. With this in mind, it is best to place adequate lighting at entry and exit points such as lobbies, ramps, stairs, and exits.

3. Place safety signs

Safety SignsAnd tags are essential to prevent slips, falls and falls. Their location warns people not to walk in dangerous places for safety.

Different areas require specific safety signals. For example, stores post "Caution: Wet Floors" signs to warn visitors of slippery floors. at the same time,construction safetyUse warning lines, control zones, and designated areas to mark which areas are passable or restricted.

4. Clean up spills immediately

Spills are one of the most common fall hazards in the workplace. They come in many forms, from a baking soda in a cafeteria to a bucket of water soaking a hospital floor. On slippery ground, the feet lose their grip and lose their balance.

If spilled, clean up as soon as possible. Sweep, mop, or mop up any substances on the floor that could cause others to slip or trip. correctcleanMake sure floors are free from harmful elements so people can walk on them safely. To prevent water from entering the floor, you can also consider various factorsDehydration methodand well pumps and other equipment.

5. Make sure you wear the right footwear

In addition to keeping the floors clean, it is also important to equip workers with the proper footwear. The right footwear protects your feet from damaging elements that can cause you to slip, trip or fall.

thisAmerican National Standards Institute (ANSI)Non-slip shoes with good grip are required. These shoes should also protect workers from static electricity, falling objects, explosions, exposure to hazardous substances, and other hazards.

Also, avoid sandals, espadrilles, high heels, and open-toed shoes when working on work surfaces. These types of footwear may increase the risk of injury.

6. Maintain and improve floor quality

fall preventionMore than just wiping up spills on the floor. This also includes paying attention to the quality of walking and working surfaces.

Modifying the floor surface can go a long way in ensuring safety against slips, falls and falls. Here are some best practices companies can use to improve floor quality:

  • Regularly inspect floors for cracks, holes, missing pieces, uneven surfaces and other hazards that could cause you to trip.
  • Invest in resilient non-slip flooring.
  • Install floor mats, abrasive coatings, pressure sensitive abrasive strips and synthetic flooring. They provide enough friction and reduce leg fatigue.

7. Implementation of safety plans and protocols

Finally, a well-thought-out safety program enhances all efforts to promote fall prevention, especially in high-risk workplaces. The plan should include the following elements:

  • Slip, trip and fall risk assessment
  • Security Standards and Practices
  • Swimming pants, trip and fall training for field workers
  • Regular inspection and maintenance
  • Security and other hardware specifications

"&""""&R[0

Eliminate manual tasks and simplify your operations.

C[-3]&"""]"" data-sheets-value="{"1":2,"2":"

"create

Eliminate manual tasks and simplify your operations.

"}">

Create your own safety plan

Eliminate manual tasks and simplify your operations.

start for free

OSHA provides guidance on safe work surfaces that companies can incorporate into their safety programs. For example, the following table showsClearance requirements for fall protection.

PlaceMinimum distance for protection against falls from heights
general industry1.22 m (4 ft)
shipyard5 feet (1.52 meters)
construction site6 stations (1.83 m)
Remote Coast Services8 feet (2.44 meters)

OSHA also includes specifications for safety equipment such as seat belts, ropes, safety nets, stair railings, handrails, andPersonal Protective Equipment (PPE).

Keep your workplace safe with SafetyCulture

SafetyCulture (formerly iAuditor)is a comprehensive digital platform that you can use to improve your fall protection efforts. Provides tools to help you manage fall safety inspections, OSHA safety andA Conversation About Building Tools, other relatedSpeech Mode in Toolkit, and more. Use SafetyCulture to:

  • edit and prepareRisk Assessment Templatefrom public libraries.
  • Protect against fallsexamineon the handset.
  • Detailed information on hardware and desktop issues with notes and photos.
  • Use it to send fall alertspossibility of action.
  • create and sharecustom reportPDF, Web and Word formats.
  • use thisanalysis teamStrengthen security measures.
Top Articles
Latest Posts
Article information

Author: Fredrick Kertzmann

Last Updated: 13/05/2023

Views: 5277

Rating: 4.6 / 5 (66 voted)

Reviews: 89% of readers found this page helpful

Author information

Name: Fredrick Kertzmann

Birthday: 2000-04-29

Address: Apt. 203 613 Huels Gateway, Ralphtown, LA 40204

Phone: +2135150832870

Job: Regional Design Producer

Hobby: Nordic skating, Lacemaking, Mountain biking, Rowing, Gardening, Water sports, role-playing games

Introduction: My name is Fredrick Kertzmann, I am a gleaming, encouraging, inexpensive, thankful, tender, quaint, precious person who loves writing and wants to share my knowledge and understanding with you.